ALL PACKAGES ARE INSURED FOR PEACE OF MIND!! AP-8030 2K Super Fill Primer/Surfacer Gray Quart Kit Kit Includes: 1 - Quart Primer 1 - Half Pint Activator Two component high build urethane primer surfacer/sealer formulated for fast dry and superior sandability. Available in gallons. Mix 5:1 with either medium or fast universal catalysts (AH6070 and AH6080). Alternatively, Super Fill Primer can be mixed 4:1 with AH6075 or AH6085. We send the AH6085 for the 4:1 mix. AP-8030 Super-Fill Primer D.T.M. is a two-component acrylic urethane primer surfacer formulated to be applied as a high build sanding primer, or a final non-sanding primer/sealer. AP-8030 offers excellent filling properties with minimal coats, fast dry, excellent adhesion, easy sanding and superior color holdout. AP-8030 does not shrink and can be tinted with basecoat tints. Products AP-8030 Super-Fill Primer D.T.M. AH-6070 Uni Activator Fast AH-6080 Uni Activator Medium AR-2040 Uni Reducer Fast AR-2050 Uni Reducer Medium AR-2060 Uni Reducer Slow AR-2100 E-Z Blend Application Surface Preparation, Bare Substrates Solvent wash surface with a good grade wax and grease remover such as AS-2900 and wipe dry with a clean cloth. Apply three single wet coats of AP AP-8300 Series Epoxy Primer according to instructions on data sheet. Surface Preparation, Pre-painted Substrates Wash surfaces with a mild detergent and hot water. Rinse with clean water and wipe dry with a clean cloth. Solvent clean with AS-2900 Clean Ease. Wipe dry with a clean cloth. Sand original paint and repair damaged areas with a good quality non-staining body filler. For spot repairs, scuff sand area where primer will be applied. For overall refinishing, scuff sand the entire car with 320 grit sandpaper or fine scuff pad. Mixing Directions, High Build, Sealer 5 Parts AP-8030 Super-Fill Primer D.T.M. 1 Part AH-6070, AH-6080 Uni Activator Series Mixing Directions, Normal Build 5 Parts AP-8030 Super-Fill Primer D.T.M. 1 Part AH-37 2K Urethane Primer Catalyst 1 Part AH-6070, AH-6080 Uni Activator Series 1 Part AR-2040, AR-2050, AR-2060 Uni Reducer Series Application, High Build and Normal Build Adjust air pressure at the gun to 30-45 psi for siphon feed guns. Use less pressure to minimize over spray on small jobs. Apply 2-3 medium wet coats at a gun distance of 8 -12 inches as needed to fill voids and block sand with 180 to 280 grit treated sandpaper. Allow 10 to 20 minutes flash time between coats. Recoat times will vary with temperature, air movement and film thickness. Insufficient flash time will promote slow hardness development of the topcoat system. Finish sand repaired area with 320 grit sandpaper using a DA Sander or hand sand. Application, Sealer Adjust air pressure at the gun to 30-45 psi for siphon feed gun. Use less pressure to minimize over spray on small jobs. Apply 1 or 2 wet coats at a gun distance of 8-12 inches. Allow 30 minutes flash time before top coating. Recoat time will vary with temperature, air movements and film thickness. Insufficient flash time will promote slow hardness development of the topcoat system. June 2007 AP-8030 pg. 2/2 Drying Schedule Dry times are based on recommended film thickness and are dependent on ambient temperature. Excessive film thicknesses, low temperature and poor air movement will retard dry times. Air Dry High Build Normal Build Sealer Dust Free 15-20 min 10-15 min 5-15 min Tack Free 25-30 min 15-20 min 15-20 min To Topcoat 60 min 45-60 min 30 min Pot Life Three to four hours for high build and normal build. Four to five hours for sealer. Accelerator To improve cure and reduce the sanding time, or for faster cure in colder conditions, add 2 to 4 ounces of AH-X99 Accelerator to one gallon of catalyzed primer. Caution: The addition of cure accelerator can significantly reduce working pot life. MADE IN THE USA Ship to the lower 48 states ONLY!!!! Always wear an approved spray mask and gear. For Questions Call Store 417 632 4894 Store Hours ~ 8:00am - 12:00pm 1:00pm - 5:00pm CST